A10VG63EP11/10R-NSC10F003D-S
EA10VS071-DR/31R-PPA12N00
A10VSO 18 DFRI/31R-PPA12N00
A10VS045DR/31RPPB12-NDD
A10VS028DR/31L A12G20+1PF2G2
A11VLO260LRDL.H2/10+A10V028
A11VL190LRDL.H2/10+A10V028
A10VO28DR/31R-PSC62K01-S1581
A10VSO100 DR /32R-VPB12N00
A10VSO100 DFR1/32R-VPB12N00
A10VSO140DRS /32R-VPB22U99
timken轴承的滚道声及其控制方法滚道声是当外球面轴承运转时，其滚动体在滚道面上滚动而发出的一种滑溜连续的声音，是所有轴承都会发生的特有的基本声。一般的轴承声即是滚道声加上其他声音。球轴承的滚道声是不规则的，频率在1Hz以上，它的主频率不随转速而变化，但其声压级随转速的加快而增加。滚道声大的轴承，其滚道声的声压级随粘度的增加而减少；而滚道声小的timken轴承，其声压级在粘度增大至约2mm2/s以上时，由减少而转为有所增大。
A10VSO140DR/31R-PPB12N00
A10VSO 28 DFR1/31R-PPA12N00
A10VSO 45 DFR1/32R-VPB12N00
A10VSO 45 DFR1/31R-PPA12N00
A10VSO 71 DRS /32R-VPB22U99
A10VSO 71 DRS/32R-VPB22U99
A10VSO 71 DFR1/31R-PPA12N00
A10VS0140FR1/31RPPB12N00
AA10VSO45DR/31R-PKC62KA3
A10VSO45DFR1/31R-VPB12N00
A10VSO71DFR1/30-PPA12N00
A10VSO100DFR1/31R-PPA12N00
A10VSO71DFR1/31R-PPA12N00-S1648
A10VSO45DFR/31R-PPA12N00
A10VSO28DFR1/31R-PPA12N00
A10VS0140DR/31R-PPB 12NOO
A10SO100DFE/31R-PPA12K52
A10VS071DFR1/32R-VPB22U99
4WRA10E1-60-22/G24K4/V
A10VSO10DR/52R-PPA12N00
A10VSO28DR/31R-PPA12NOO
A10VSO28DR/31R-PPA12N00
A10VSO45DFR1/31R-PPA12NOO
A10VS0100DFR1/32R-VPB12N00
A10VS018DFR1/31R-PPA12N00
A10VSO100DR/31R-PPA12N00
E-A10VSO71DFR/31R-PPA12NOO
A10VS0100DR/32R-VPB12N00
A10VSO71DR/31R-PPA12N00
A10VSO140DRS/32R-VPB12N00
A10VSO18DR/31R-PPA12N00
A10VSO71DFR1/32R-VPB22U99
A10VSO28DFR1(DR)/31R-PPA12N00
A10VS071DFR1/32R-PPB12N00
A10VSO71DFR/31R-PPA12N00
A10VSO45DR/31R-PPA12N00
A10VS071DR/31R-PPA12
A10VSO28DFR1/31RPPA12NOO
A10VS028DFR1/31R-PPA12N00-S032
A10VSO100DFLR/31R-VPA12N00
A10VS018DR/52R-PPA14N00
A10VS0100DR/32R-VPB22(12)U99(N00)
HED40A10/315=HED80A20/315
A10VSO018DFR1
A10VSO100DFR1/31R-PPA12NOO
A10VS071DFR1/31R
A10VSO71DFR1/31RR-PPA12N00
A10VSO28DFR1/31L-PSC62K02
A10VSO45DFR1/32R-VPB12N00
A10VSO18DR/31R-VKC62K01
A10VSO18DFR1/31R-VPA12N00
A10VS045DFR1/31R-PPA12N00
A10VSO100DRＧ/31R-PPA12N00
A10VSO71DFR
A10VSO28DFR
A10VSO140DFR1
A10VS028DR/30R-PPA12N00
A10VS071DFR1/31R-PPA12N00-S1648
A10VO100DFLR/31R-PSC62K01
A10VO100DFR1/32R-VPB12NOO
A10VSO100DFLR/31R-PPA12N00
A10VSO45DR/31R-PSC62K02
A10VS180FR1/31R-PPA12N00
A10V0100DR/31R-PSC11N00
两种方法均易出现裂纹、硬点,焊补后不容易进行机械加工。焊条价格便宜。用镍基铸铁焊条Z38焊条焊补，焊层与焊层之间应停顿冷却至6℃以下，焊补区少气孔、裂纹产生,机械加工性良好，结合强度高、无脱落现象,由于机床导轨加工后吸油及焊条吹力的影响,易产生咬边、形成焊补痕迹,焊补区颜色与母材有很大区别,而且焊条价格昂贵。从分析的结果就可以得出：传统焊补工艺不能解决机床导轨缺陷修复的根本原因是统的喷焊、电弧焊工艺,焊补后易产生裂纹，工件易受热变形,容易出现二次气孔，焊补处金属颜色与母材差异大是其共同的特点。
