武汉星兴达液压气动设备有限公司为您提供更多油泵型号，可来电咨询！
A10VSO10DRG/52R-PSC14N00-SO857
A10VSO10DRG/52R-PSC64N00
A10VSO10DRG/52R-PUC14N00
A10VSO10DRG/52R-PUC64N00
A10VSO10DRG/52R-PUC64N00-SO857
A10VSO18DR/31R-PPA12N00
A10VSO18DR/31R-PPA12K01
A10VSO18DFR1/31R-PPA12N00
A10VSO18DFR1/31R-PPA12N00
A10VSO18DFR1/31R-PPA12K01
A10VSO18DFR/31R-PPA12N00
A10VSO18DFLR/31R-PPA12N00
A10VSO18DG/31R-PPA12N00
A10VSO18DRG/31R-PPA12N00
A10VSO18DFE1/31R-PPA12N00
A10VSO18FHD/31R-PPA12N00
A10VSO18ED/31R-PPA12N00
A10VSO28DR/31R-PPA12N00
A10VSO28DR/31R-PPA12K01
A10VSO28DFR1/31R-PPA12N00
A10VSO28DFR1/31R-PPA12N00
A10VSO28DFR1/31R-PPA12K01
A10VSO28DFR/31R-PPA12N00
A10VSO28DFLR/31R-PPA12N00
A10VSO28DG/31R-PPA12N00
A10VSO28DRG/31R-PPA12N00
A10VSO28DFE1/31R-PPA12N00
A10VSO28FHD/31R-PPA12N00
A10VSO28ED/31R-PPA12N00
A10VSO45DR/31R-PPA12N00
A10VSO45DR/31R-PPA12K01
A10VSO45DFR1/31R-PPA12N00
A10VSO45DFR1/31R-PPA12N00
A10VSO45DFR1/31R-PPA12K02
A10VSO45DFR/31R-PPA12N00
A10VSO45DFR/31R-PPA12K01
A10VSO45DFR/31R-PPA12K26
A10VSO45DFLR/31R-PPA12N00
A10VSO45DG/31R-PPA12N00
A10VSO45DRG/31R-PPA12N00
A10VSO45DFE1/31R-PPA12N00
A10VSO45FHD/31R-PPA12N00
A10VSO45ED/31R-PPA12N00
A10VSO71DR/31R-PPA12N00
A10VSO71DR/31R-PPA12K01
A10VSO71DFR1/31R-PPA12N00
A10VSO71DFR1/31R-PPA12K02
A10VSO71DFR/31R-PPA12N00
A10VSO71DFR/31R-PPA12K27
A10VSO71DFLR/31R-PPA12N00
C形：有两种刀尖角。刀尖角的两个刀尖强度高，一般做成75车刀，用来粗车外圆、端面，8刀尖角的两个刃口强度较高，用它不用换刀即可加工端面或圆柱面，在内孔车刀中一般用于加工台阶孔。R形：圆形刃口，用于特殊圆弧面的加工，刀片利用率高，但径向力大。W形：三个刃口且较短，刀尖角8刀尖强度较高，主要用在普通车床上加工圆柱面和台阶面。D形：两个刃口且较长，刀尖角55刀尖强度较低，主要用于仿形加工，当做成93车刀时切入角不得大于27～3;做成62.5车刀时，切入角不得大于57～6，在加工内孔时可用于台阶孔及较浅的清根。
