元氏力士乐A10VSO71DR/31L-PP

武汉星兴达液压气动设备有限公司为您提供更多型号！欢迎咨询来电！
要提高中空玻璃的隔热性能，一般是增大空间的厚度和使用惰性气体，这些惰性气体性能稳定，具有惰性和热传导率低的特点，用惰性气体置换中空玻璃内部的空气，这样可减少传导，但空间层不宜过大，墨盒里的间隙是6mm-12mm左右，要降低辐射传热，选用一般镀膜玻璃或低辐射镀膜玻璃控制各种射线透过，达到降低辐射、传热的目的。计算和实验数据显示：通常单片玻璃的传热系数k=6W。元氏力士乐A10VSO71DR/31L-PP

A10VSO45DFR1/31R-PPA12N00
A10VSO28DRG/31R-PPA12N00
A10VS045DFR/31R-PPA12NOO
A10VSO100DFLR/31R-PPA12N00
A10VS0100DFR1/32R-VPB22U99N00
A10VSO45DR/31R-PPA12K01
A10VSO28DFR1/31L-PSC62K02
A10VS018DR/52R-PPA14N00
A10VSO18DFR1/31R-PPB12N00
A10VSO10DR/52R-PPA14N00
A10VS071DR/31R-PPA12N00
A10VSO140D/31R-PPB12N00
A10VSO100DFR1/32R-PPB12NOO
A10VSO100DFR1/31R-PPA12K01
A10VSO100DR/31R-VPA12N00
A10VSO45ED/31R-PPA12N00
A10VSO28DR/32R-PPA121V00
A10VSO71DRG/31L-PPA12N00
A10VS071DFR1/32R-PPB12N00
A10VSO100DR/31R-PPA12NOO
A10VSO18ED/31R-PPA12N00
A10VSO18DFR1/31R-PPA12N00
A10VSO28DFR/31R-PPA12N00
A10VSO-140DR/31R-PPB12N00

A10VSO71DFR/31R-PPA12NOO
A10VSO45DR/52R-PC12N00
A10VSO18DRG/31R-PPA12N00
A10VSO45DFR/31R-PPA12N00
A10VSO100FHD/31R-PPA12N00
A10VSO45DRG/31R-PPA12N00
A10VSO71DFR1/31R-PPA12K02
A10VSO140DFR/32R-PPB12N00
A10VSO28DFLR/31R-PPA12N00
A10VSO28DRG/31L-PPA12N00
A10VSO18DRG/31R-PPA12N00
A10VSO28DFLR/31R-PPA12N00

A10VS018DFR1/31RPPA12N00
A10VSO100DR/32R-VPB12N00
A10VSO140DFR1/31R-PPA12N00
A10VSO18DFR/31R-PPA12N00
A10VSO100DFR1/31R-PPA12K01
A10VSO100DFLR/31R-PPA12N00
A10VSO28DFR1/32R-VPB12N00
A10VSO100DFLR/31R-PPA12N00
A10VSO100DFR1/31R-PPA12K
A10VSO28DR/31R-PPA12K01
A10VSO71DRS/32R-VPB22U99
A10VSO28DFR1/31R-PPA12K01
A10VSO45DG/31R-PPA12N00
A10VSO28DRG/31R-PPA12N00
A10VSO45 DFR31R-PSA12NOO
A10VSO100DFR1/31R-PPA12N00
切割生产率切割生产率或叫切割效率，为锯片的切割深度与进给速度的乘积，即单位时间内切割材料的截面积，用cm2/min或m2/hr表示。实践表明，对于同一种材料，同时提高切割深度和进给速度，虽然能提高切割生产率，但锯片的非正常磨损也加剧，使用寿命要下降，同时锯切功率也加大，故增加了切割成本。一般地，切割较软材料或强研磨性材料时可采用一次成型切割；中径锯片大多用于切割板材，也多为一次切割；而中硬以上花岗石则应采用分步切割。