联系方式西门子一级代理商联系人 万工

联系方式西门子一级代理商联系人 万工

联系方式西门子一级代理商联系人 万工

联系方式西门子一级代理商联系人 万工

SIEMENS（西门子销售中心）

 上海朕锌电气设备有限公司

zx-plc.com ）

联系人：万紫云（销售经理）

手 机：（微信同步）

Q Q：27798 23058 zx-plc.com ）

座 机：

公司网址http://zhenxindianqi.cn/ 

概述

CU230P‑2 Control Units

CU230P‑2 PN Control Unit

The Control Unit performs closed-loop control functions for the inverter.

The CU230P-2 Control Units are designed for drives with integrated technological functions for pump, fan and compressor applications.

The I/O interface, the fieldbus interfaces and the additional software functions optimally support these applications. The integration of technological functions is a significant differentiating feature to the other Control Units of the SINAMICS G120 drive family.

The CU230P-2 Control Units can be operated with the following Power Modules:

• PM240‑2

• PM240

• PM250

Note:

The CU230P‑2 is the Control Unit for SINAMICS G120P and SINAMICS G120P Cabinet for pumps, fans and compressors.
Please refer to Catalog D 35 for more information.

Note:

Shield plates and shield connection kits are available. These can be used in the wiring installation for the Control Units and Power Modules to ensure that it complies with EMC guidelines.
For more information about shield connection kits and shield plates for Control Units and Power Modules, please refer to section "Supplementary system components".

Typical, integrated HVAC/HLK functions

• Linear and quadratic torque characteristic for fluid flow and positive displacement machines

• ECO mode for additional energy saving in U/f control mode

• 2 analog inputs (current/voltage can be selected) to directly connect pressure/level sensors

• 2 additional analog inputs to connect Pt1000/LG‑Ni1000 temperature sensors

• Direct control of valves and flaps using two 230 V AC relays

• Automatic restart

• Flying restart

• Skip frequencies

• Hibernation mode

• Load check function to monitor belts and flow

• Cascade connection

• 4 integrated PID controllers (e.g. for temperature, pressure, air quality, level)

• Multi-zone controller

• Essential service mode

• Real time clock with three time generators

IOP wizards for special applications

• Pumps: Positive displacement (constant load torque) and centrifugal pumps (square load torque) with and without PID controller

• Fans: Radial and axial fans (square load torque) with and without PID controller

• Compressors: Positive displacement (constant load torque) and fluid flow machines (square load torque) with and without PID controller

Control Unit CU240E‑2

CU240E‑2 DP‑F Control Unit

The Control Unit performs closed-loop control functions for the inverter.

The CU240E‑2 Control Unit is designed as standard Control Unit for all of the usual applications involving U/f or vector control.

• CU240E-2 series with standard I/O quantity structure and integrated safety technology

The CU240E‑2 Control Unit can be combined with the following Power Modules:

• PM240‑2

• PM240

• PM250

Note:

Shield plates and shield connection kits are available. These can be used in the wiring installation for the Control Units and Power Modules to ensure that it complies with EMC guidelines.
For more information about shield connection kits and shield plates for Control Units and Power Modules, please refer to section "Supplementary system components".

Safety Integrated functions

The safety function "Safe Torque Off" (STO) (certified according to IEC 61508 SIL 2 and EN ISO 13849‑1 PL d and Category 3) is already integrated into the basic versions of the CU240E‑2 series (CU240E‑2, CU240E‑2 DP, CU240E‑2 PN).

With the fail-safe variants of the CU240E-2 series (CU240E‑2 F, CU240E‑2 DP-F, CU240E‑2 PN-F), the fail-safe SINAMICS G120 inverter provides five safety functions which are certified according to IEC 61508 SIL 2 and EN ISO 13849‑1 PL d and Category 3:

• Safe Torque Off (STO)
  to protect against active movement of the drive

• Safe Stop 1 (SS1)
  for continuous monitoring of a safe braking ramp

• Safely Limited Speed (SLS)
  for protection against dangerous movements when a speed limit is exceeded (the CU240E‑2 DP‑F Control Unit has up to 4 selectable SLS limit values)

• Safe Direction (SDI)
  This function ensures that the drive can only rotate in the selected direction.

• Safe Speed Monitor (SSM)
  This function signals if a drive operates below a specific speed/feed velocity (only CU240E‑2 DP‑F / CU240E‑2 PN‑F with PROFIsafe).

These functions can be activated by means of PROFIsafe or via the safety inputs.

None of the safety functions require a motor encoder and they are thus much cheaper and easier to implement. Existing systems in particular can be simply updated with safety technology without the need to change the motor or mechanical system.

The Safe Torque Off (STO) function can be used without restriction for all applications. The SS1, SLS, SDI and SSM functions are only permissible for applications where the load can never accelerate when the inverter is switched off. They are therefore not permitted for applications involving pull-through loads such as hoisting gear and unwinders.

Additional information is provided in chapter Highlights, section Safety Integrated.

CU250S‑2 Control Units

CU250S-2 Control Unit

The Control Unit performs closed-loop control functions for the inverter.

The CU250S‑2 Control Units are designed as standard Control Units for all of the usual applications involving V/f or vector control.

CU250S‑2 Control Units can be used to implement all common applications involving V/f or vector control as well as applications for drives with positioning requirements. This expansion allows them to be used in lifting, swiveling, traversing or rotating applications. The positioning functionality is comparable with SINAMICS S110 servo drives.

Two points must be noted here:

• Vector control (VC) and sensorless vector control (SLVC) are possible

• Positioning possible via one encoder or in parallel using two encoders

The CU250S‑2 Control Units can be combined with the following Power Modules:

• PM240‑2

• PM240

• PM250

Note:

Shield plates and shield connection kits are available for use in the wiring installation of Control Units and Power Modules to ensure that it complies with EMC guidelines.

For more information about shield connection kits and shield plates for Control Units and Power Modules, please refer to section "Supplementary system components".

Safety Integrated functions

The following Safety Integrated Basic Functions (certified according to IEC 61508 SIL 2 and EN ISO 13849‑1 PL d and Category 3) are integrated as standard in the CU250S-2 series:

• Safe Torque Off (STO)
  to protect against active movement of the drive

• Safe Stop 1 (SS1)
  for continuous monitoring of a safe braking ramp

• Safe Brake Control (SBC) is used to safely control a holding
  brake

The following Safety Integrated Extended Functions (certified according to IEC 61508 SIL 2 and EN ISO 13849‑1 PL d and Category 3) are optionally available for the CU250S-2 series:

• Safely Limited Speed (SLS)
  for protection against dangerous movements on exceeding a speed limit

• Safe Direction (SDI)
  This function ensures that the drive can only rotate in the selected direction.

• Safe Speed Monitor (SSM)
  This function signals if a drive operates below a specific speed/feed velocity.

These functions can be activated by means of PROFIsafe or via the safety inputs.

None of the safety functions require a motor encoder and they are thus much cheaper and easier to implement. Existing systems in particular can be simply updated with safety technology without the need to change the motor or mechanical system.

The Safe Torque Off (STO) function can be used without restriction for all applications. The SS1, SLS, SDI and SSM functions are only permissible for applications where the load can never accelerate when the inverter is switched off. They are therefore not permitted for applications involving pull-through loads such as hoisting gear and unwinders.

Additional information is provided in chapter Highlights, section Safety Integrated.

设计

CU230P‑2 HVAC, CU230P‑2 DP and CU230P‑2 PN Control Units

CU230P‑2 Control Unit with open and closed terminal covers

Terminal No.	Signal	Features
Digital inputs (DI) – Standard
69	DI COM	Reference potential for digital inputs
5 ... 8, 16.17	DI0 … DI5	Freely programmable isolated, inputs in compliance with IEC 61131-2
Digital outputs (DO)
18	DO0, NC	Relay output 1 NC contact (5 A, 30 V DC or 2 A, 250 V AC) 1)
19	DO0, NO	Relay output 1 NO contact (5 A, 30 V DC or 2 A, 250 V AC)
20	DO0, COM	Relay output 1 Common contact (5 A, 30 V DC or 2 A, 250 V AC) 1)
21	DO1, NO	Relay output 2 NO contact (0.5 A, 30 V DC)
22	DO1, COM	Relay output 2 Common contact (0.5 A, 30 V DC)
23	DO2, NC	Relay output 3 NC contact (5 A, 30 V DC or 2 A, 250 V AC) 1)
24	DO2, NO	Relay output 3 NO contact (5 A, 30 V DC or 2 A, 250 V AC)
25	DO2, COM	Relay output 3 Common contact (5 A, 30 V DC or 2 A, 250 V AC) 1)
Analog inputs (AI)
3	AI0+	Differential input, switchable between current, voltage Value range: 0 ... 10 V, -10 ... +10 V, 0/2 ... 10 V, 0/4 ... 20 mA
4	AI0-
10	AI1+	Differential input, switchable between current, voltage Value range: 0 ... 10 V, -10 ... +10 V, 0/2 ... 10 V, 0/4 ... 20 mA
11	AI1-
50	AI2+	Non-isolated input, switchable between current and temperature sensors, type Pt1000/LG-Ni1000 Value range: 0/4 ... 20 mA, Pt1000 -50 ... +250 °C;  LG‑Ni1000 -50 ... +150 °C
51	GND	Reference potential of the AI2/internal electronics ground
52	AI3+	Non-isolated input for temperature sensors, type Pt1000/LG‑Ni1000 Value range:  Pt1000: -50 ... +250 °C;  LG‑Ni1000: -50 ... +150 °C
53	GND	Reference potential of the AI3/internal electronics ground
Analog outputs (AO)
12	AO0+	Non-isolated output Freely programmable Value range: 0 ... 10 V; 0/4 ... 20 mA
13	GND	Reference potential of the AO0/internal electronics ground
26	AO1+	Non-isolated output Freely programmable Value range: 0 ... 10 V; 0/4 ... 20 mA
27	GND	Reference potential of the AO1/internal electronics ground
PTC/KTY interface
14	T1 MOTOR	Positive input for motor temperature sensor Type: PTC, KTY, bil
15	T2 MOTOR	Negative input for motor temperature sensor
Power supply
9	+24 V OUT	Power supply output 24 V DC, max. 100 mA
28	GND	Reference potential of the power supply/internal electronics ground
1	+10 V OUT	Power supply output 10 V DC ±0.5 V, max. 10 mA
2	GND	Reference potential of the power supply/internal electronics ground
31	+24 V IN	Power supply input 20.4 ... 28.8 V DC, max. 1500 mA
32	GND IN	Reference potential of the power supply input
35	+10 V OUT	Power supply output 10 V DC ±0.5 V, max. 10 mA
36	GND	Reference potential of the power supply/internal electronics ground

¹⁾ The following applies to systems complying with UL: A maximum of 3 A, 30 V DC or 2 A, 250 V AC may be connected via terminals 18 / 20 (DO0 NC) and 23 / 25 (DO2 NC).

CU240E‑2, CU240E‑2 DP, CU240E‑2 PN, CU240E‑2 F, CU240E‑2 DP‑F and CU240E‑2 PN‑F Control Units

CU240E‑2 Control Unit with open and closed terminal covers

Terminal No.	Signal	Features
Digital inputs (DI) – Standard
5 ... 8, 16.17	DI0 … DI5	Freely programmable (isolated) 5.5 mA/24 V
69	DI COM1	Reference potential for digital inputs 0, 2, 4, 6
34	DI COM2	Reference potential for digital inputs 1, 3, 5, 7
Digital inputs (DI) – Fail-safe (formed from two standard inputs using the appropriate parameter setting)
16, 17	F-DI0	Fail-safe digital inputs, 2 channels (redundant), freely programmable (isolated) 5.5 mA/24 V
The following are only available for CU240E‑2 F, CU240E‑2 DP‑F and CU240E‑2 PN‑F
5, 6	F-DI0	Fail-safe digital inputs, 2 channels (redundant), freely programmable (isolated) 5.5 mA/24 V
7, 8	F-DI1	Fail-safe digital inputs, 2 channels (redundant), freely programmable (isolated) 5.5 mA/24 V
16, 17	F-DI2	Fail-safe digital inputs, 2 channels (redundant), freely programmable (isolated) 5.5 mA/24 V
Digital outputs (DO)
18	DO0, NC	Relay output DO0 NC contact (0.5 A, 30 V DC)
19	DO0, NO	Relay output DO0 NO contact (0.5 A, 30 V DC)
20	DO0, COM	Relay output DO0 Common contact (0.5 A, 30 V DC)
21	DO1+	Transistor output DO1 Positive (0.5 A, 30 V DC)
22	DO1-	Transistor output DO1 Negative (0.5 A, 30 V DC)
23	DO2, NC	Relay output DO2 NC contact (0.5 A, 30 V DC)
24	DO2, NO	Relay output DO2 NO contact (0.5 A, 30 V DC)
25	DO2, COM	Relay output DO2 Common contact (0.5 A, 30 V DC)
Analog inputs (AI)
3	AI0+	Differential input, switchable between current, voltage Value range: 0 ... 10 V, -10 ... +10 V, 0/2 ... 10 V, 0/4 ... 20 mA
4	AI0-
10	AI1+	Differential input, switchable between current, voltage Value range: 0 ... 10 V, -10 ... +10 V, 0/2 ... 10 V, 0/4 ... 20 mA
11	AI1-
Analog outputs (AO)
12	AO0+

内蒙古省供货地区：

呼和浩特市 包头市 乌海市 赤峰市 通辽市 鄂尔多斯市 呼伦贝尔市 巴彦淖尔市  锡林郭勒盟

新疆自治区供货地区：

乌鲁木齐市 石河子市 克拉玛依市 和田市 阿图仕市 阿克苏市 喀什市 库尔勒市 吐鲁番市

西藏自治区供货地区：

拉萨 林芝 昌都 日喀则

云南省供货地区：

昆明市 曲靖市 玉溪市 丽江市 普洱市 保山市 昭通市 临沧市

贵州省供货地区：

贵阳市 遵义市 安顺市 凯里市 铜仁市 毕节市 都匀市 六盘水市 兴义市

四川省供货地区：

成都市 自贡市 攀枝花市 泸州市 德阳市 绵阳市 广元市 遂宁市 内江市 乐山市 南充市 宜宾市 广安市 达州市 巴中市 雅安市 眉山市 资阳市

广西省供货地区：

南宁市 桂林市 柳州市 梧州市 钦州市 北海市 玉林市 贵港市 防城港市 百色市  来宾市

电源模板

6ES72881SR200AA0

6ES72881ST200AA0

6ES72881SR300AA0

6ES72881ST300AA0

6ES72881SR400AA0

6ES72881ST400AA0

6ES72881SR600AA0

6ES72881ST600AA0

6ES72881CR400AA0

6ES72881CR600AA0

6ES72882DE080AA0

6ES72882DR080AA0

6ES72882DT080AA0

6ES72882DR160AA0

6ES72882DT160AA0

6ES72882DR320AA0

6ES72882DT320AA0

6ES72883AE040AA0

6ES72883AE080AA0

6ES72883AQ020AA0

6ES72883AQ040AA0

6ES72883AM030AA0

6ES72883AM060AA0

6ES72883AR020AA0

6ES72883AR040AA0

6ES72883AT040AA0

6ES72887DP010AA0

6ES72880CD100AA0

6ES72880ED100AA0

6ES72885CM010AA0

6ES72885DT040AA0

6ES72885AE010AA0

6ES72885AQ010AA0

6ES72885BA010AA0

6AV66480BC113AX0

6AV66480BE113AX0

6AV66480CC113AX0

6AV66480CE113AX0

6ES72110AA230XB0

6ES72110BA230XB0

6ES72121AB230XB0

6ES72121BB230XB0

6ES72141AD230XB0

6ES72141BD230XB0

6ES72142AD230XB0

6ES72142AS230XB0

6ES72142BD230XB0

6ES72162AD230XB0

6ES72162BD230XB0

6ES72121AB230XB8

6ES72121BB230XB8

6ES72141AD230XB8

6ES72141BD230XB8

6ES72142AD230XB8

6ES72142AS230XB8

6ES72142BD230XB8

6ES72162AD230XB8

6ES72162BD230XB8

6ES72211BF220XA0

6ES72211BH220XA0