不当的拆卸振动筛NTN轴承，可能造成NTN轴承内部的损坏。污染物可能进入NTN轴承或再安装时可能产生的错误。拆卸振动筛轴承必须十分小心，轴心必须有适当的支撑，否则拆卸力量可能伤及NTN轴承。外围的拆卸拆卸过盈配合的外圈，事先在外壳的圆周上设置几处外圈挤压螺杆用螺丝，一面均等地拧紧螺杆.一边拆卸。这些螺杆孔平常盖上盲塞，振动筛圆锥滚子轴承等的分离型轴承，在外壳挡肩上设置几处切口，使用垫块，用压力机拆卸，或轻轻敲打着拆卸。
A10VO18DFR1/31R-PPA12N00
A10VSO28DFR1/31R-PPA12N00
A10VSO45DFR1/31R-PPA12N00
A10VSO71DFR1/31R-PPA12N00
A10VSO100DFR1/31R-PPB12N00
A10VSO140DFR1/31R-PPA12N00
A10VSO45DFR1/32R-PPB12N00
A10VSO100DFR1/32R-PPB12N00
A10VSO071DFR1/32R-VPB12N00
A10VSO140DFR1/32R-VPB12N00
A10VSO140DRS/32R-VPB22U99
A10VSO140DFLR1/31R-PPB12KO1
A10VS0100DR/31R-PPA12N00
A10VS018DR/31R-PPA12N00
A10V028DR/31R-PSC12N00
A10VG18HD1/10L-NSC16N003E
A10VS028DR/31R-PPA12N00
A10VS045DR/31R-PPA12K25
A10VSO045DR/31R-PPA12N00
A10VSO71DFR1/31R-PPA12KB5
A10VSO28DRF1/31R-PSA12N00
A10VSO100DFR1/31R-PPA12K
A10VSO100DFR1/31R-PPA12KB3
A10VS010DR
A10VSO71DFR/31R-PSC62K07
A10VS045DFR1/31RPPA12NOO
A10V071DFRI/34 PSC6402-S0225
A10VSO-140DR/31R-PPB12N00
A10VS0-71FR1/31R-PPA12N00
A10VS071DFR1/31R-PPB12NOO
MA10VSO100PFR1/31R-PPA12N00
E-A10VSO140DFR1/31R-PPA12N00
E-A10VSO71DFR1/31R-PPA12N00
E-A10VSO45DFR1/31R-PPA12N00
E-A10VSO28DFR1/31R-PPA12N00
A10VO 71DFR1/31RPSC62K07
三螺杆泵拆卸步骤:1,螺杆泵与电机脱离,排空介质（防止电机,有毒介质伤人）;拆卸螺杆泵排出体;拆卸螺杆泵定子,必要时按泵轴方向盘动轴作辅助;拆卸转子及中间轴;拆卸传动轴和轴封;长期不用的螺杆泵,要作防锈处理,方法为用防锈脂涂抹非油漆金属表面,包括轴表面,填料壳体内腔等,并进行润滑.螺杆泵装配时,注意事项:1,装配时应将螺杆泵零件仔细清洗,检查,损坏的零件应更换;传动轴两万向接头装配时,应检查密封圈有否损坏,在空腔内填充润滑脂;正确安装的轴承使轴转动灵活,无卡阻现象.4,轴封安装:填料函安装时,应使填料压盖压紧螺栓位置在壳体安装窗口内,便于扳手调整螺栓;排出体压紧固定时,螺母拧紧应均匀一致;机械密封安装应小心,摩擦副端面应清洁并涂上润滑脂;安装定子时,用润滑油涂抹转子,定子内腔表面,有利于定子安装;安装装配时,联轴器安装偏差:Y.2mm,3。
