武汉星兴达液压气动设备有限公司为您提供更多油泵型号，可来电咨询！
A10VSO10DRG/52R-PSC14N00-SO857
A10VSO10DRG/52R-PSC64N00
A10VSO10DRG/52R-PUC14N00
A10VSO10DRG/52R-PUC64N00
A10VSO10DRG/52R-PUC64N00-SO857
A10VSO18DR/31R-PPA12N00
A10VSO18DR/31R-PPA12K01
A10VSO18DFR1/31R-PPA12N00
A10VSO18DFR1/31R-PPA12N00
A10VSO18DFR1/31R-PPA12K01
A10VSO18DFR/31R-PPA12N00
A10VSO18DFLR/31R-PPA12N00
A10VSO18DG/31R-PPA12N00
A10VSO18DRG/31R-PPA12N00
A10VSO18DFE1/31R-PPA12N00
A10VSO18FHD/31R-PPA12N00
A10VSO18ED/31R-PPA12N00
A10VSO28DR/31R-PPA12N00
A10VSO28DR/31R-PPA12K01
A10VSO28DFR1/31R-PPA12N00
A10VSO28DFR1/31R-PPA12N00
A10VSO28DFR1/31R-PPA12K01
A10VSO28DFR/31R-PPA12N00
A10VSO28DFLR/31R-PPA12N00
A10VSO28DG/31R-PPA12N00
A10VSO28DRG/31R-PPA12N00
A10VSO28DFE1/31R-PPA12N00
A10VSO28FHD/31R-PPA12N00
A10VSO28ED/31R-PPA12N00
A10VSO45DR/31R-PPA12N00
A10VSO45DR/31R-PPA12K01
A10VSO45DFR1/31R-PPA12N00
A10VSO45DFR1/31R-PPA12N00
A10VSO45DFR1/31R-PPA12K02
A10VSO45DFR/31R-PPA12N00
A10VSO45DFR/31R-PPA12K01
A10VSO45DFR/31R-PPA12K26
A10VSO45DFLR/31R-PPA12N00
A10VSO45DG/31R-PPA12N00
A10VSO45DRG/31R-PPA12N00
A10VSO45DFE1/31R-PPA12N00
A10VSO45FHD/31R-PPA12N00
A10VSO45ED/31R-PPA12N00
A10VSO71DR/31R-PPA12N00
A10VSO71DR/31R-PPA12K01
A10VSO71DFR1/31R-PPA12N00
A10VSO71DFR1/31R-PPA12K02
A10VSO71DFR/31R-PPA12N00
A10VSO71DFR/31R-PPA12K27
A10VSO71DFLR/31R-PPA12N00
刚开始的几支棒要加大牵引拉力，出材正常后可慢慢调回拉力。般情况下，出材速度可控制在3-4m/min.2.3.7生产过程中严格按合金状态要求进行淬火，风冷或水冷。常生产过程中不允许随意停机，如因设备故障出现停机，停机过3分钟，模具必须卸模回炉加温，再次上机模具温度要保证达到5℃。但是为保证型材质量，建议将模具卸模送煲后再次上机生产，因多孔模对温度等要求较高，回炉模具再次上机造成型材偏壁、压烂模具的情况时有发生。4出料口型材温度及速度控制2.4.1根据出料口型材温度适时调整铝棒加热温度。2出料口型材温度正常控制范围在52-58℃之间，温度低于52℃型材容易造成硬度不够，达不到相应的力学性能，高于58℃随时可能发生拉烂、劏模现象。3出料后型材目视观察表面变黑，必须马上降低棒温和挤压速度，以防出料型材温度高。4多孔模生产过程中，机手必须时刻观察棒温、出料口型材温度、型材表面、设备运行情况，一旦发生意外情况，必须立即停机，否则模具损坏率极高，对模具使用寿命有很大影响。一模多孔挤压设备铝型材挤压是一个系统工程，要*实现一模多孔技术，达成提高挤压成品率及生产效率、增强出材稳定性的目的，除了要注重挤压机的稳定性与模具质量之外，同时配置*的配套设备，如双牵引机带飞锯的机台、模具、铝棒加热炉、长锭炉热剪技术等设备也是至关重要的。结束语挤压一模多孔技术随着挤压生产工艺的不断提高优化，其生产效率、成品率不断提高。因企业采用的设备、模具材质、挤压工艺的差异，在一模多孔技术上的发展亦有所差别。
