武汉星兴达液压气动设备有限公司为您提供更多油泵型号，可来电咨询！
A10VSO10DFR1/52R-PPA14N00-S1482
A10VSO10DFR1/52R-PPA14N00-SO857
A10VSO10DFR1/52R-PPA14N00-SO858
A10VSO10DFR1/52R-PSA14N00-S1915
A10VSO10DFR1/52R-PSA14N00-SO 32
A10VSO10DFR1/52R-PSC14N00
A10VSO10DFR1/52R-PSC14N00-SO 32
A10VSO10DFR1/52R-PSC64N00
A10VSO10DFR1/52R-PSC64N00E
A10VSO10DFR1/52R-PSC64N00ES1768
A10VSO10DFR1/52R-PSC64N00-S1768
A10VSO10DFR1/52R-PUC64N00
A10VSO10DFR1/52R-PUC64N00E
A10VSO10DFR1/52R-PUC64N00E
A10VSO10DFR1/52R-PUC64N00-SO857
A10VSO10DFR1/52R-VPA14N00
A10VSO10DFR1/52R-VUC64N00
A10VSO10DR/52R-PSA14N00-S1482
A10VSO10DR/52R-PSA14N00-SO32
A10VSO10DR/52R-PSA14N00-SO857
A10VSO10DR/52R-PSC64N00
A10VSO10DR/52R-PSC64N00E
A10VSO10DR/52R-PSC64N00-SO858
A10VSO10DR/52R-PSC64N00-SO922
A10VSO10DR/52R-PUC14N00
A10VSO10DR/52R-PUC14N00
A10VSO10DR/52R-PUC64N00
A10VSO10DR/52R-PUC64N00E
A10VSO10DR/52R-PUC64N00-S1768
A10VSO10DR/52R-PUC64N00-SO857
A10VSO10DR/52R-PUC64N00-SO858
A10VSO10DR/52R-VKC64N00ES1768
A10VSO10DR/52R-VKC64N00-S1768
A10VSO10DR/52R-VPA14N00
A10VSO10DR/52R-VPA14N00-SO857
A10VSO10DR/52R-VSC64N00-SO857
A10VSO10DRG/52L-PSC64N00
A10VSO10DRG/52L-PUC64N00
A10VSO10DRG/52R-PKC14N00
A10VSO10DRG/52R-PKC64N00
A10VSO10DRG/52R-PKC64N00E
A10VSO10DRG/52R-PKC64N00-SO846
A10VSO10DRG/52R-PKC64N00-SO857
A10VSO10DRG/52R-PKC64N00-SO858
A10VSO10DRG/52R-PPA14N00
A10VSO10DRG/52R-PPA14N00-SO857
A10VSO10DRG/52R-PPA14N00-SO858
A10VSO10DRG/52R-PPC14N00
A10VSO10DRG/52R-PSC14N00
塞尺又称测微片或厚薄规。使用前必须先清除塞尺和工件上的污垢与灰尘。使用时可用一片或数片重叠插入间隙，以稍感拖滞为宜。测量时动作要轻，不允许硬插。也不允许测量温度较高的零件。塞尺使用注意事项使用卡尺前须确认是否经校验及在校验有效期内；不允许在测量过程中剧烈弯折塞尺，或用较大的力硬将塞尺插入被检测间隙，否则将损坏塞尺的测量表面或零件表面的精度；根据结合面的间隙情况选用塞尺片数，但片数愈少愈好；不能测量温度较高的工件；用塞尺时必须注意正确的方法(测间隙必须垂直被测面，测断差必须放平)；读数时，按塞标尺片上所标数值直接读数即可；塞尺必须定时保养；使用完后，应将塞尺擦拭干净，并涂上一薄层工业凡士林，然后将塞尺折回夹框内，以防锈蚀、弯曲、变形而损坏；塞尺不用时必须放入盒子保护以防生锈变色而影响使用；存放时，不能将塞尺放在重物下，以免损坏塞尺。
