A11VO260LRDU2/11R-NZD12N00H-S柱塞泵的工作原理
柱塞泵是液压系统的一个重要装置。它依靠柱塞在缸体中往复运动，使密封工作容腔的容积发生变化来实现吸油、压油。柱塞泵具有额定压力高、结构紧凑、效率高和流量调节方便等优点，被广泛应用于高压、大流量和流量需要调节的场合，诸如液压机、工程机械和船舶中。
柱塞泵是往复泵的一种，属于体积泵，其柱塞靠泵轴的偏心转动驱动，往复运动，其吸入和排出阀都是单向阀。当柱塞外拉时，工作室内压力降低，出口阀关闭，低于进口压力时，进口阀打开，液体进入;柱塞内推时，工作室压力升高，进口阀关闭，高于出口压力时，出口阀打开，液体排出。当传动轴带动缸体旋转时，斜盘将柱塞从缸体中拉出或推回，完成吸排油。
A11VO260LRDU2/11R-NZD12N00H-SA11VO260LRDU2/11R-NZD12N00H-S
产品型号:
A11VO40LRS/10R-NSC12N00
A11VO40LRS/10R-NPC12N00
A11VO40LRH2/10R-NSC12N00
A11VO40LRH2/10R-NPC12N00
A11VO40DRS/10R-NSC12N00
A11VO40DRS/10R-NPC12N00
A11VO60LRS/10R-NSC12N00
A11VO60LRS/10R-NPC12N00
A11VO60LRS/10R-NSC12K01
A11VO60LRS/10R-NPC12K01
A11VO60LRH2/10R-NSC12N00
A11VO60LRH2/10R-NPC12N00
A11VO60LRH2/10R-NSC12K01
A11VO60LRH2/10R-NPC12K01
A11VO60DRS/10R-NSC12N00
A11VO60DRS/10R-NPC12N00
A11VO60DRS/10R-NSC12K01
A11VO60DRS/10R-NPC12K01
A11VO75LRS/10R-NSD12N00
A11VO75LRS/10R-NPD12N00
A11VO75LRS/10R-NSD12K01
A11VO75LRS/10R-NPD12K01
A11VO75LRH2/10R-NSD12N00
A11VO75LRH2/10R-NPD12N00
A11VO75LRH2/10R-NSD12K01
A11VO75LRH2/10R-NPD12K01
A11VO75DRS/10R-NSD12N00
A11VO75DRS/10R-NPD12N00
A11VO75DRS/10R-NSD12K01
A11VO75DRS/10R-NPD12K01
A11VO95LRS/10R-NSD12N00
A11VO95LRS/10R-NPD12N00
A11VO95LRS/10R-NSD12K01
A11VO95LRS/10R-NPD12K01
A11VO95LRH2/10R-NSD12N00
A11VO95LRH2/10R-NPD12N00
A11VO95LRH2/10R-NSD12K01
A11VO95LRH2/10R-NPD12K01
A11VO95DRS/10R-NSD12N00
A11VO95DRS/10R-NPD12N00
A11VO95DRS/10R-NSD12K01
A11VO95DRS/10R-NPD12K01
A11VO130LRS/10R-NSD12N00
A11VO130LRS/10R-NPD12N00
压滤机在每次运行时，前需要对整机作检查，需要调试正常的压滤机方可进料工作。检查的内容有：机械压紧传动部件及减速箱必须加足润滑油；液压压紧复查油箱贮油量及液压站工作压力，液压油一般每年更换一次，这样可以减少对压滤机机器的损耗。待一切正常后方可压紧滤板加压过滤，过滤压力和过滤温度必须在规定范围之内，过滤压力过高会引起渗漏，过滤温度过高塑料滤板易变形，加料时悬浮液要浓度均匀。不得有混杂物；卸饼后滤布及滤板必须冲洗干净，不允许残渣粘贴在密封面或进料通道内，否则会影响进料畅通及滤板的密封性，从而相起因滤板两侧压力不平衡，导致滤板变形损坏。
以上型号不全~可咨询~
