A11VO40EP2/10R-NSC12N00H柱塞液压泵

A11VO40EP2/10R-NSC12N00H柱塞液压泵柱塞泵的工作原理

   柱塞泵是液压系统的一个重要装置。它依靠柱塞在缸体中往复运动，使密封工作容腔的容积发生变化来实现吸油、压油。柱塞泵具有额定压力高、结构紧凑、效率高和流量调节方便等优点，被广泛应用于高压、大流量和流量需要调节的场合，诸如液压机、工程机械和船舶中。

   柱塞泵是往复泵的一种，属于体积泵，其柱塞靠泵轴的偏心转动驱动，往复运动，其吸入和排出阀都是单向阀。当柱塞外拉时，工作室内压力降低，出口阀关闭，低于进口压力时，进口阀打开，液体进入;柱塞内推时，工作室压力升高，进口阀关闭，高于出口压力时，出口阀打开，液体排出。当传动轴带动缸体旋转时，斜盘将柱塞从缸体中拉出或推回，完成吸排油。
A11VO40EP2/10R-NSC12N00H柱塞液压泵A11VO40EP2/10R-NSC12N00H
产品型号:
A11VO40LRS/10R-NSC12N00

A11VO40LRS/10R-NPC12N00

A11VO40LRH2/10R-NSC12N00

A11VO40LRH2/10R-NPC12N00

A11VO40DRS/10R-NSC12N00

A11VO40DRS/10R-NPC12N00

A11VO60LRS/10R-NSC12N00

A11VO60LRS/10R-NPC12N00

A11VO60LRS/10R-NSC12K01

A11VO60LRS/10R-NPC12K01

A11VO60LRH2/10R-NSC12N00

A11VO60LRH2/10R-NPC12N00

A11VO60LRH2/10R-NSC12K01

A11VO60LRH2/10R-NPC12K01

A11VO60DRS/10R-NSC12N00

A11VO60DRS/10R-NPC12N00

A11VO60DRS/10R-NSC12K01

A11VO60DRS/10R-NPC12K01

A11VO75LRS/10R-NSD12N00

A11VO75LRS/10R-NPD12N00

A11VO75LRS/10R-NSD12K01

A11VO75LRS/10R-NPD12K01

A11VO75LRH2/10R-NSD12N00

A11VO75LRH2/10R-NPD12N00

A11VO75LRH2/10R-NSD12K01

A11VO75LRH2/10R-NPD12K01

A11VO75DRS/10R-NSD12N00

A11VO75DRS/10R-NPD12N00

A11VO75DRS/10R-NSD12K01

A11VO75DRS/10R-NPD12K01

A11VO95LRS/10R-NSD12N00

A11VO95LRS/10R-NPD12N00

A11VO95LRS/10R-NSD12K01

A11VO95LRS/10R-NPD12K01

A11VO95LRH2/10R-NSD12N00

A11VO95LRH2/10R-NPD12N00

A11VO95LRH2/10R-NSD12K01

A11VO95LRH2/10R-NPD12K01

A11VO95DRS/10R-NSD12N00

A11VO95DRS/10R-NPD12N00

A11VO95DRS/10R-NSD12K01

A11VO95DRS/10R-NPD12K01

A11VO130LRS/10R-NSD12N00

A11VO130LRS/10R-NPD12N00
五.产品使用须知使用时用3-5%碳酸纳溶液反复冲洗，再用清水冲，然后消毒测试PH值达许可范围。检查底盘和快装上的圈放置是否正确，筒体和底盘连接必须对称拧紧快装螺丝，防液体外漏。安装滤膜前，将下面的螺杆拧紧，固定在底盘上，放上底盘固定圈(和底盘之间也要加装滤材)，再安装滤板和滤框，将选用的滤材分别贴在滤板和滤框上，滤材内孔放在过滤板和框的凸出处内，重复直至到安装完毕，顶部盖上压板并压紧顶板（直径5以上的过滤器先把中间的固定螺丝压紧，然后必须对称的压紧边上的4个螺杆，注意防止倾斜密封不够）。

以上型号不全~可咨询~