深圳市鑫博恒业科技有限公司
地址：深圳市福田区华强北都会大厦B座27楼S室
电话：
http://www.xb5j.com E-mail:info@xb5j.cn
QQ: 800062763
IDRA33-DC
iSeries PID控制器和信号调节器
iDR Series
5年保修 新产品! CE
iSeries PID控制器和信号调节器
iDR Series:iSeries PID控制器和信号调节器
IDR
通用输入
热电偶
- RTD
过程电压
过程的电流
应变
多输出
以太网TCP / IP
串行RS232／RS485
-自调整PID控制
2形式的“C”继电器
2直流脉冲
可编程：
可扩展的模拟电压，0至10伏直流电；
模拟电流，0至20毫安
高精度：±0.5°C（0.9°F），0.03%为
全自动调谐PID控制
用户友好，简单的配置
内置的激励
插头连接器
免费软件
欧米茄?IDR DIN导轨系列是一个家庭的基于微处理器的仪器提供3种尺寸。该仪器有一个类似的设置和配置菜单和操作方法，这是一个大的系统集成，极大的节省时间。
IDR仪器提供一个广阔的选择信号输入。选择容易地选择从远程程序员的菜单，4个前面板按钮，或通过串口或以太网通信。
IDR处理10种常见类型的热电偶，多RTDS和几个过程（DC）电压和电流范围。该模型还具有内置的激励，24 VDC @ 25毫安。它的输入信号的广泛的选择，这是测量或用热电偶，温度控制的一个很好的选择，或4至20 mA变送器。
仪器的应变和过程（ISDR模型）测量输入称重传感器，压力传感器，和大多数的应变仪传感器以及过程中的电压和电流范围。这是具有内置的5或10伏直流励磁桥式传感器，5伏或10伏40毫安@ @ 60毫安（5和24伏之间的任何电压是可以通过特殊的顺序）。该模型支持4 -和6线桥通信，比例测量。
国际减灾战略特点的快速和容易的“过程”校准/缩放的信号输入到任何单位工程。该模型还具有10点线性化，它允许用户将输入信号的非线性传感器的各种极。
IDR提供简单的手动开/关操作或全自动调谐PID控制（选择预置调，自适应调整，PID，PI，PD控制模式）。双重控制输出可配置为多种独立的控制和报警的应用程序，如热/冷/热，热，热/冷/报警，凉爽，凉爽/报警，或报警/报警。坡道定点功能允许用户定义的速率上升到设定值，大限度地减少热冲击负载在启动。对于那些只需要简单的菜单和没有PID控制，限位报警（铝）选项。
用户可以选择几乎任何组合2控制或报警输出：固态继电器（SSR）形成的“C”SPDT继电器和脉冲10 VDC输出使用一个外部的SSR。
可选的模拟输出可以被编程在范围0到10伏或0到20毫安。它是可选的或一个控制输出，或作为一个校准的重传过程的功能控制器之间的价值。
远程程序员/显示可以被编程为在任何给定值或报警点改变颜色。例如，该仪器可以编程，显示过程值在琥珀中的绿色在预热过程中，信号的正常工作范围，并在红色信号报警状态。
嵌入式Web服务器选项允许你直接连接到以太网网络和TCP / IP数据包中的标准数据传输服务的网页，或者在局域网或互联网。以串行通信选项，用户可以从RS232，RS422，RS485之间的按钮和菜单选择，简单的ASCII命令或Modbus。
规格：
Universal Temperature and Process Input Model (iDR)
Accuracy: ±0.5°C temp; 0.03% rdg process
Resolution: 1°/0.1° 10 μV process
Temperature Stability:
RTD: 0.04°C/°C
T/C @ 25°C (77°F): 0.05°C/°C cold-junction compensation
Process: 50 ppm/°C
NMRR: 60 dB
CMRR: 120 dB
A/D Conversion: Dual-slope
Reading Rate: 3 samples per second
Digital Filter: Programmable
Input Types: Thermocouple, RTD, analog voltage, analog current
Thermocouple Lead Resistance: 100 Ω max
Thermocouple Type (ITS 90): J, K, T, E, R, S, B, C, N, L
RTD Input (ITS 68): 100/500/1000 Ω Pt sensor; 2-, 3- or 4-wire; 0.00385 or 0.00392 curve
Voltage Input: 0 to 100 mV, 0 to 1 V, 0 to 10 Vdc
Input Impedance: 10 MΩ for 100 mV, 1 MΩ for 1 or 10 Vdc
Current Input: 0 to 20 mA (5 Ω load)
Configuration: Single-ended
Polarity: Unipolar
Step Response: 0.7 s for 99.9%
Decimal Selection: None, 0.1 for temperature; none, 0.1, 0.01 or 0.001 for process
Setpoint Adjustment: -1999 to 9999 counts
Span Adjustment: 0.001 to 9999 counts
Offset Adjustment: -1999 to 9999
Excitation: 24 Vdc @ 25 mA (not available with "-DC", "-C24" or "-C4EIT" option)
Universal Strain and Process Input Model (iSDR)
Accuracy: 0.03% rdg
Resolution: 10/1 μV
Temperature Stability: 50 ppm/°C
NMRR: 60 dB
CMRR: 120 dB
A/D Conversion: Dual-slope
Reading Rate: 3 samples per second
Digital Filter: Programmable
Input Types: Analog voltage, analog current
Voltage Input: 0 to 100 mVdc, -100 mVdc to 1 Vdc, 0 to 10 Vdc
Input Impedance: 10 MΩ for 100 mV; 1 MΩ for 1 or 10 Vdc
Current Input: 0 to 20 mA (5 Ω load)
Linearization Points: Up to 10
Configuration: Single-ended
Polarity: Unipolar
Step Response: 0.7 s for 99.9%
Decimal Selection: None, 0.1, 0.01 or 0.001
Setpoint Adjustment: -1999 to 9999 counts
Span Adjustment: 0.001 to 9999 counts
Offset Adjustment: -1999 to 9999
Excitation: 5 Vdc @ 40 mA; 10 Vdc @ 60 mA (not available with "-DC", "-C24" or "-C4EIT" option
Control
Action: Reverse (heat) or direct (cool)
Modes: Time and amplitude proportional control modes; selectable manual or auto PID, proportional, proportional with integral, proportional with derivative with anti-reset windup and on/off
Rate: 0 to 399.9 seconds
Reset: 0 to 3999 seconds
Cycle Time: 1 to 199 seconds; set to 0 for on/off operation
Gain: 0.5 to of span; setpoints 1 or 2
Damping: 0000 to 0008
Soak: 00.00 to 99.59 (HH:MM), or off
Ramp to Setpoint:
00.00 to 99.59 (HH:MM), or off
Autotune: Operator-initiated from front panel
Control Output 1 and 2
Relay: 250 Vac or 30 Vdc @ 3 A (resistive load); configurable for on/off, PID and ramp and soak
Output 1: SPDT type, can be configured as alarm 1 output
Output 2: SPDT type, can be configured as alarm 2 output
SSR: 20 to 265 Vac @ 0.05 to 0.5 A (resistive load); continuous
DC Pulse: Non-isolated; 10 Vdc @ 20 mA Analog Output (Output 1 Only): Non-isolated, proportional 0 to 10 Vdc or 0 to 20 mA; 500 Ω max Analog Output (Optional Output 3): Isolated, retransmission, 0 to 10 Vdc or 0 to 20 mA, 500 Ω max; accuracy is 1% of FS, for scaling gain from 0.03 to 100 mV per count. Isolation is 1000 Vdc; linearity is 0.2%
Network and Communications Options (-C24, -C4EIT, -EIT)
Ethernet: Standards compliance IEEE 802.3 10 Base-T
Supported Protocols: TCP/IP, ARP, HTTPGET
RS232/RS422/RS485/MODBUS: Selectable from menu; both ASCII and MODBUS protocol selectable from menu. Programmable 300 to 19.2K baud; complete programmable setup capability; program to transmit current display, alarm status, min/max, actual measured input value and status.
RS485: Addressable from 0 to 199
Connection: Screw terminals
Alarm 1 and 2 (Programmable)
Type: Same as output 1 and 2
Operation: High/low, above/below, band, latch/unlatch, normally open/normally closed and process/deviation
Analog Output (Programmable): Non-isolated, retransmission, 0 to 10 Vdc or 0 to 20 mA, 500 Ω max (output 1 only); accuracy is ±1% of FS when the following conditions are satisfied:
1. Input is not scaled below 1% of input FS
2. Analog output is not scaled below 3% of output FS
General
Line Voltage/Power: 90 to 240 Vac ±10%, 50 to 400 Hz*, 110 to 375 Vdc, equivalent voltage. No CE compliance above 60 Hz.
Low-Voltage/Power Option: 24 Vac**; 12 to 36 Vdc; 20 to 36 Vdc for Ethernet and isolated analog output from qualified safety approved source ** Units can be powered safely with 24 Vac power, but no certification for CE/UL is claimed.
Insulation
Power to Input/Output: 2300 Vac per 1-minute test 1500 Vac per 1-minute test (for low-voltage power option)
Power to Relays/SSR Outputs: 2300 Vac per 1-minute test Relays/SSR to Relay/SSR Outputs: 2300 Vac per 1-minute test
RS232/485 to Input/Outputs: 500 Vac per 1-minute test
Environmental Conditions: 0 to 55°C (32 to 131°F) (0 to 50°C for UL), 90% RH (non-condensing)
Approvals:
UL, C-UL, CE per EN61010-1:2001, FM (temperature units only)
产品型号 产品描述
iDR Temperature/process (no outputs)
iDR22-EI Temperature/process, Two solid state relays (SSRs): 0.5 A @ 120/240 Vac continuous, Ethernet with
iDRA Temp/process (no outputs) w/ isolated analog output
iDRA-C24-DC Temperature/process w/ isolated analog output, Isolated RS-232 and RS-485, 300 to 19.2K baud and MODBUS, 12 to 36 Vdc (20 to 36 Vdc for iDRA), 24 Vac
iSDR Strain/process (no outputs)
ISDR24-C4EI Strain/process, SSR and pulsed 10 Vdc @ 20 mA (for use with external SSR), Ethernet with
选配件
iDRP Remote programmer/display
Software (Requires Network Option)
OPC-SERVER LICENSE OPC server/driver software license
注释:
1. "-DC", "-C24" or "-C4EIT" not available with excitation.
2. Analog output (option 5) is not available with "-AL" units.
3. Ethernet options are not available for the iDRA controller.
4. "iDRA0*-AL": 1 analog retransmission and 1 alarm.
5. 20 to 36 Vdc for "-C4EIT" and "-EIT"
产品型号说明
(1) (2) (3) (4) (5)
选项描述
(1) Series
选择
iDR 代表 Temperature/process
iDRA 代表 Temp/process w/ isolated analog output *3
iSDR 代表 Strain/process
(2) Control Outputs
选择
Nothing(leave field blank) 代表 Temperature/process with 2 control outputs
22 代表 Two solid state relays (SSRs) - 0.5 A @ 120/240 Vac continuous
23 代表 SSR and relay - Form C SPDT 3 A @ 120 Vac 3 A @ 240 Vac
24 代表 SSR and pulsed 10 Vdc @ 20 mA (for use with external SSR)
33 代表 2 relays - Form ‘C’ SPDT 3 A @ 120 Vac 3 A @ 240 Vac
42 代表 Pulsed 10 Vdc @ 20 mA (for use with external SSR) and SSR
43 代表 Pulsed 10 Vdc @ 20 mA (for use with external SSR) and relay - Form C SPDT 3 A @ 120 Vac 3 A @ 240 Vac
44 代表 Two pulsed 10 Vdc @ 20 mA (for use with external SSR)
52 代表 Analog output selectable as either control or retransmission of process value 0 to 10 Vdc or 0 to 20 mA @ 500 max and SSR
53 代表 Analog output 0 to 10 Vdc or 0 to 20 mA @ 500 max and relay
54 代表 Analog output 0 to 10 Vdc or 0 to 20 mA @ 500 max and pulse 10 Vdc
(3) Network Options
选择
Nothing(leave field blank) 代表 No option
-C24 代表 Isolated RS232 and RS485 300 to 19.2K baud and MODBUS*1
-EIT 代表 Ethernet with
-C4EIT 代表 Ethernet with
(4) Power Supply
选择
Nothing(leave field blank) 代表 Standard power input - 90 to 240 Vac/Vdc. 50 to 400 Hz (no entry required)
-DC 代表 12 to 36 Vdc (20 to 36 Vdc for iDRA) 24 Vac*1
(5) Factory Setup
选择
Nothing(leave field blank) 代表 No option
-FS 代表 Factory setup and configuration
IDRA33-DC
IDR24-C24
IDR24-C24-DC
IDR24-C4EIT
IDR24-C4EIT-DC
IDR24-DC
IDR24-EIT
IDR24-EIT-DC
IDR33
IDR33-C24
IDR33-C24-DC
ISDR43-C24
ISDR43-C24-DC
ISDR43-DC
ISDR44
ISDR44-C24
ISDR44-C24-DC
ISDR44-DC
ISDR52
ISDR52-C24
ISDR52-C24-DC
ISDR52-DC
ISDR53
ISDR53-C24
ISDR53-C24-DC
ISDR53-DC
ISDR54
ISDR54-C24
ISDR54-C24-DC
ISDR54-DC
ISDR23-C24
ISDR23-C24-DC
ISDR23-DC
ISDR24
ISDR24-C24
ISDR24-C24-DC
ISDR24-DC
ISDR33
ISDR33-C24
ISDR33-C24-DC
ISDR33-C4EIT
ISDR33-C4EIT-DC
IDR53-DC
IDR53-EIT
IDR53-EIT-DC
IDR54
IDR54-C24
IDR54-C24-DC
IDR54-C4EIT
IDR54-C4EIT-DC
IDR54-DC
IDR54-EIT
IDR54-EIT-DC
IDR44-C4EIT-DC
IDR44-DC
IDR44-EIT
IDR44-EIT-DC
IDR52
IDR52-C24
IDR52-C24-DC
IDR52-C4EIT
IDR52-C4EIT-DC
IDR52-DC
IDR43-C24-DC
IDR43-C4EIT
IDR43-C4EIT-DC
IDR43-DC
IDR43-EIT
IDR43-EIT-DC
IDR44
IDR44-C24
IDR44-C24-DC
IDR44-C4EIT
IDR33-C4EIT
IDR33-C4EIT-DC
IDR33-DC
IDR33-EIT
IDR33-EIT-DC
IDR42
IDR42-C24
IDR42-C24-DC
IDR23-C24
IDR23-C24-DC
IDR23-C4EIT
IDR23-C4EIT-DC
IDR23-DC
IDR23-EIT
IDR23-EIT-DC
IDR24
IDR52-EIT
IDR52-EIT-DC
IDR53
IDR53-C24
IDR53-C24-DC
IDR53-C4EIT
IDR53-C4EIT-DC
IDRA22
IDRA22-C24
IDRA22-C24-DC
IDRA22-DC
IDRA23
IDRA23-C24
IDRA23-C24-DC
IDRA23-DC
IDRA24
IDRA24-C24
IDRA24-C24-DC
IDRA24-DC
CNIDRA22
CNIDRA22-C24
ISDR33-DC
ISDR33-EIT
ISDR33-EIT-DC
ISDR42
ISDR42-C24
ISDR42-C24-DC
ISDR42-DC
ISDR43IDR22
IDR22-C24
IDR22-C24-DC
IDR22-C4EIT
IDR22-C4EIT-DC
IDR22-DC
IDR22-EIT
IDR22-EIT-DC
IDR23
CNIDRA22-C24-DC
CNIDRA22-DC
CNIDRA23
CNIDRA23-C24
CNIDRA23-C24-DC
CNIDRA23-DC
CNIDRA24
CNIDRA24-C24
CNIDRA24-C24-DC
CNIDRA24-DC
IDRA33
IDRA33-C24
IDRA33-C24-DC
IDRA33-DC
IDRA42
IDRA42-C24
IDRA42-C24-DC
IDRA42-DC
IDRA43
IDRA43-C24
IDRA43-C24-DC
IDRA43-DC
IDRA44
IDRA44-C24
IDRA44-C24-DC
IDRA44-DC
CNIDRA42
CNIDRA42-C24
CNIDRA42-C24-DC
CNIDRA42-DC
IDR42-C4EIT
IDR42-C4EIT-DC
IDR42-DC
IDR42-EIT
IDR42-EIT-DC
IDR43
IDR43,FS
IDR43-C24
CNIDRA43
CNIDRA43-C24
CNIDRA43-C24-DC
CNIDRA43-DC
CNIDRA44
CNIDRA44-C24
CNIDRA44-C24-DC
CNIDRA44-DC
ISDR22
ISDR22-C24
ISDR22-C24-DC
ISDR22-DC
ISDR23
IDRA33-DC
IDRA33-DC
