A11VO260EP2D/11R-NZD12K67H-S斜轴液压泵河北秦皇岛

A11VO260EP2D/11R-NZD12K67H-S斜轴液压泵河北秦皇岛柱塞泵的工作原理

   柱塞泵是液压系统的一个重要装置。它依靠柱塞在缸体中往复运动，使密封工作容腔的容积发生变化来实现吸油、压油。柱塞泵具有额定压力高、结构紧凑、效率高和流量调节方便等优点，被广泛应用于高压、大流量和流量需要调节的场合，诸如液压机、工程机械和船舶中。

   柱塞泵是往复泵的一种，属于体积泵，其柱塞靠泵轴的偏心转动驱动，往复运动，其吸入和排出阀都是单向阀。当柱塞外拉时，工作室内压力降低，出口阀关闭，低于进口压力时，进口阀打开，液体进入;柱塞内推时，工作室压力升高，进口阀关闭，高于出口压力时，出口阀打开，液体排出。当传动轴带动缸体旋转时，斜盘将柱塞从缸体中拉出或推回，完成吸排油。
A11VO260EP2D/11R-NZD12K67H-S斜轴液压泵河北秦皇岛河北秦皇岛A11VO260EP2D/11R-NZD12K67H-S
产品型号:
A11VO40LRS/10R-NSC12N00

A11VO40LRS/10R-NPC12N00

A11VO40LRH2/10R-NSC12N00

A11VO40LRH2/10R-NPC12N00

A11VO40DRS/10R-NSC12N00

A11VO40DRS/10R-NPC12N00

A11VO60LRS/10R-NSC12N00

A11VO60LRS/10R-NPC12N00

A11VO60LRS/10R-NSC12K01

A11VO60LRS/10R-NPC12K01

A11VO60LRH2/10R-NSC12N00

A11VO60LRH2/10R-NPC12N00

A11VO60LRH2/10R-NSC12K01

A11VO60LRH2/10R-NPC12K01

A11VO60DRS/10R-NSC12N00

A11VO60DRS/10R-NPC12N00

A11VO60DRS/10R-NSC12K01

A11VO60DRS/10R-NPC12K01

A11VO75LRS/10R-NSD12N00

A11VO75LRS/10R-NPD12N00

A11VO75LRS/10R-NSD12K01

A11VO75LRS/10R-NPD12K01

A11VO75LRH2/10R-NSD12N00

A11VO75LRH2/10R-NPD12N00

A11VO75LRH2/10R-NSD12K01

A11VO75LRH2/10R-NPD12K01

A11VO75DRS/10R-NSD12N00

A11VO75DRS/10R-NPD12N00

A11VO75DRS/10R-NSD12K01

A11VO75DRS/10R-NPD12K01

A11VO95LRS/10R-NSD12N00

A11VO95LRS/10R-NPD12N00

A11VO95LRS/10R-NSD12K01

A11VO95LRS/10R-NPD12K01

A11VO95LRH2/10R-NSD12N00

A11VO95LRH2/10R-NPD12N00

A11VO95LRH2/10R-NSD12K01

A11VO95LRH2/10R-NPD12K01

A11VO95DRS/10R-NSD12N00

A11VO95DRS/10R-NPD12N00

A11VO95DRS/10R-NSD12K01

A11VO95DRS/10R-NPD12K01

A11VO130LRS/10R-NSD12N00

A11VO130LRS/10R-NPD12N00
一般情况下，塑料挤出机生产产品模温过低时容易产生应力，应适当提高温度。但当注射速度较高时，即使模温低一些，也可减低应力的产生。注射和保压时间过长也会产生应力，将其适当缩短或进行Th次保压切换效果较好。非结晶性树脂，如AS树脂、ABS树脂、PMMA树脂等较结晶性树脂如聚、聚甲醛等容易产生残余应力，应予以注意。脱模推出时，由于脱模斜度小、模具型胶及凸模粗糙，使推出力过大，产生应力，有时甚至在推出杆周围产生白化或破裂现象。

以上型号不全~可咨询~